Skip to content
FiftyCalc Free calculators for all 50 states

Two-Sample t Interval Calculator

Test cases replayed : 3 of 3 match · Methodology · No outside source listed

Enter the mean, standard deviation and size of two independent samples and a confidence level. You get the confidence interval for the difference of the population means, with its margin of error.

Result

Sample figures

Confidence interval for μ₁ − μ₂—

Point estimate x̄₁ − x̄₂ —

  • Standard error of the difference—
  • Degrees of freedom (ν)—
  • Critical value t*—
  • Margin of error t* × SE—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Two-Sample t Interval Calculator

Sample 1 mean (x̄₁): enter a number. Prefilled example: 52.3.

Sample 1 standard deviation (s₁): enter 0 or more. Prefilled example: 6.1.

Sample 1 size (n₁): enter 2 or more. Prefilled example: 30.

Sample 2 mean (x̄₂): enter a number. Prefilled example: 48.9.

Sample 2 standard deviation (s₂): enter 0 or more. Prefilled example: 7.4.

Sample 2 size (n₂): enter 2 or more. Prefilled example: 25.

Confidence level, in percent: enter a number from 50 to 99.9. Prefilled example: 95.

Variance assumption

Variance assumption: choose Unequal variances (Welch) or Equal variances (pooled). Prefilled example: Unequal variances (Welch).

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Sample 1 mean (x̄₁): enter a number.
  2. Sample 1 standard deviation (s₁): enter 0 or more.
  3. Sample 1 size (n₁): enter 2 or more.
  4. Sample 2 mean (x̄₂): enter a number.
  5. Sample 2 standard deviation (s₂): enter 0 or more.
  6. Sample 2 size (n₂): enter 2 or more.
  7. Confidence level, in percent: enter a number from 50 to 99.9.
  8. Variance assumption: choose Unequal variances (Welch) or Equal variances (pooled).
  9. Read the result: Confidence interval for μ₁ − μ₂; the panel also shows Point estimate x̄₁ − x̄₂, Standard error of the difference, Degrees of freedom (ν), Critical value t* and Margin of error t* × SE.

How this calculator works

Interval = (x̄₁ − x̄₂) ± t* × SE, where t* is the quantile of Student's t distribution with ν degrees of freedom that leaves (1 − confidence) ÷ 2 in each tail.

Welch: SE = √(s₁²/n₁ + s₂²/n₂) and ν = (s₁²/n₁ + s₂²/n₂)² ÷ [(s₁²/n₁)²/(n₁ − 1) + (s₂²/n₂)²/(n₂ − 1)] (Welch–Satterthwaite). Pooled: s_p² = [(n₁ − 1)s₁² + (n₂ − 1)s₂²] ÷ (n₁ + n₂ − 2), SE = s_p √(1/n₁ + 1/n₂) and ν = n₁ + n₂ − 2. These are the formulas of the NIST/SEMATECH e-Handbook of Statistical Methods, section 1.3.5.3, and of this site's t-test calculator.

The fractional Welch degrees of freedom are used as they are, without rounding. Results are shown with up to 4 decimal places.

Worked example

Sample 1 mean (x̄₁)52.3
Sample 1 standard deviation (s₁)6.1
Sample 1 size (n₁)30
Sample 2 mean (x̄₂)48.9
Sample 2 standard deviation (s₂)7.4
Sample 2 size (n₂)25
Confidence level95%
Variance assumptionUnequal variances (Welch)
Confidence interval for μ₁ − μ₂(-0.3272, 7.1272)
Point estimate x̄₁ − x̄₂3.4
Standard error of the difference1.8522
Degrees of freedom (ν)46.5289
Critical value t*2.0123
Margin of error t* × SE3.7272

Frequently asked questions

What does it mean if the interval contains 0?

At that confidence level the data are consistent with no difference between the two means. A two-sided t-test at the matching significance level (5% for a 95% interval) would not reject equal means.

Welch or pooled?

Welch's interval does not assume equal variances and is the usual default. The pooled interval is valid only if both populations have the same variance; with unequal sample sizes it can be noticeably narrower or wider than Welch's.

My textbook uses the smaller of n₁ − 1 and n₂ − 1 as degrees of freedom. Why is the answer different?

That is a conservative shortcut for hand calculation; it gives a wider interval. Software and the NIST handbook use the Welch–Satterthwaite value shown here.

Questions answered

Related calculators