Skip to content
FiftyCalc Free calculators for all 50 states

Angle of Twist Calculator

Test cases replayed : 2 of 2 match · Methodology · No outside source listed

A shaft under torque twists along its length. Enter the torque, the length, the diameters and the shear modulus of the material.

Result

Sample figures

Angle of twist—°

Polar moment of inertia J (mm⁴) —

  • Angle of twist (radians)—
  • Maximum shear stress at the surface (MPa)—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Angle of Twist Calculator

Torque, in N·m: enter a number. Prefilled example: 500.

Shaft length, in m: enter 0 or more. Prefilled example: 1.5.

Outside diameter, in mm: enter 0 or more. Prefilled example: 40.

Inside diameter (0 for solid), in mm: enter 0 or more. Prefilled example: 0.

Material (shear modulus G): choose Carbon steel (about 79.3 GPa), Aluminum alloy (about 26 GPa), Titanium alloy (about 44 GPa) or Brass (about 37 GPa). Prefilled example: Carbon steel (about 79.3 GPa).

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Torque, in N·m: enter a number.
  2. Shaft length, in m: enter 0 or more.
  3. Outside diameter, in mm: enter 0 or more.
  4. Inside diameter (0 for solid), in mm: enter 0 or more.
  5. Material (shear modulus G): choose Carbon steel (about 79.3 GPa), Aluminum alloy (about 26 GPa), Titanium alloy (about 44 GPa) or Brass (about 37 GPa).
  6. Read the result: Angle of twist; the panel also shows Polar moment of inertia J (mm⁴), Angle of twist (radians) and Maximum shear stress at the surface (MPa).

How this calculator works

Angle of twist φ = T × L ÷ (J × G) for a circular shaft in elastic torsion, with T the torque, L the length, G the shear modulus and J the polar moment of inertia: J = π × (D⁴ − d⁴) ÷ 32 for outside diameter D and inside diameter d.

Maximum shear stress τ = T × r ÷ J at the outer radius r = D ÷ 2. Shear moduli are typical handbook values; use your material's datasheet for design. The formula holds only below the yield stress.

The formula

  1. J=π×(do4−di4)32
  2. φ=t×lJ×(1×10−12)×gm×1,000,000,000
  3. P=deg⁡(φ)
Symbols used in the formula
SymbolMeaningUnit
tTorqueN·m
lShaft lengthm
doOutside diametermm
diInside diameter (0 for solid)mm
gmMaterial (shear modulus G)
JPolar moment of inertia J (mm⁴)
φAngle of twistradians
PAngle of twist°
deg(x)the angle x, converted from radians to degrees.

Worked example

Torque500 N·m
Shaft length1.5 m
Outside diameter40 mm
Inside diameter (0 for solid)0 mm
Material (shear modulus G)Carbon steel (about 79.3 GPa)
Polar moment of inertia J (mm⁴)251,327.4123
Angle of twist (radians)0.0376
Maximum shear stress at the surface (MPa)39.7887
  1. J=3.14159×(404−04)32=251,327.41
  2. φ=500×1.5251,327.41×(1×10−12)×79.3×1,000,000,000=0.0376312
  3. P=deg⁡(0.0376312)=2.15611

Angle of twist 2.1561 °

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

How much does a 40 mm steel shaft twist under 500 N·m over 1.5 m?

About 2.16°, with a surface shear stress near 39.8 MPa.

Why are hollow shafts used?

Material near the center adds little to J, so a tube saves weight for nearly the same stiffness.

Questions answered

Related calculators