Skip to content
FiftyCalc Free calculators for all 50 states

Langelier Saturation Index Calculator

Test cases replayed : 3 of 3 match · Methodology · No outside source listed

Enter the test results of your water. The calculator gives the pH at which the water is just saturated with calcium carbonate, the Langelier index (scale-forming or corrosive tendency) and the Ryznar index.

Result

Sample figures

Langelier Saturation Index, LSI—

Tendency of the water —

  • Saturation pH, pHs—
  • Ryznar Stability Index, RSI—
  • Temperature used (°C)—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Langelier Saturation Index Calculator

Measured pH: enter a number from 0 to 14. Prefilled example: 7.5.

Water temperature: enter a number. Prefilled example: 80.

Temperature unit

Temperature unit: choose °F or °C. Prefilled example: °F.

Calcium hardness (mg/L or ppm as CaCO₃): enter 0.01 or more. Prefilled example: 300.

Alkalinity (mg/L or ppm as CaCO₃): enter 0.01 or more. Prefilled example: 100.

Total dissolved solids, TDS (mg/L or ppm): enter 0.01 or more. Prefilled example: 1,000.

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Measured pH: enter a number from 0 to 14.
  2. Water temperature: enter a number.
  3. Temperature unit: choose °F or °C.
  4. Calcium hardness (mg/L or ppm as CaCO₃): enter 0.01 or more.
  5. Alkalinity (mg/L or ppm as CaCO₃): enter 0.01 or more.
  6. Total dissolved solids, TDS (mg/L or ppm): enter 0.01 or more.
  7. Read the result: Langelier Saturation Index, LSI; the panel also shows Tendency of the water, Saturation pH, pHs, Ryznar Stability Index, RSI and Temperature used (°C).

How this calculator works

LSI = pH − pHs, with pHs = 9.3 + A + B − C − D, where A = (log₁₀ TDS − 1) ÷ 10, B = −13.12 × log₁₀(°C + 273) + 34.55, C = log₁₀(calcium hardness as CaCO₃) − 0.4 and D = log₁₀(alkalinity as CaCO₃), all in mg/L.

Ryznar Stability Index RSI = 2 pHs − pH. Formulas and readings (LSI > 0 tends to precipitate, 0 equilibrium, < 0 tends to corrode) as given in Table 1 of García-Ávila et al., Data in Brief 18 (2018), doi 10.1016/j.dib.2018.03.007 (PMC5996164), read on Europe PMC on October 28, 2026.

Temperatures in °F are converted with °C = (°F − 32) × 5 ÷ 9. The LSI is shown to two decimals and its sign gives the reading.

The formula

  1. Tc={(t−32)×59if tf≠0totherwise
  2. Fa=log10⁡(tds)−110
  3. Fb=−13.12×log10⁡(Tc+273)+34.55
  4. Fc=log10⁡(ca)−0.4
  5. Fd=log10⁡(alk)
  6. Pv=9.3+Fa+Fb−Fc−Fd
  7. Lv=ph−Pv
Symbols used in the formula
SymbolMeaningUnit
phMeasured pH
tWater temperature
caCalcium hardness (mg/L or ppm as CaCO₃)
alkAlkalinity (mg/L or ppm as CaCO₃)
tdsTotal dissolved solids, TDSmg/L or ppm
tfOne if Temperature unit is °F, zero otherwise
TcResult of step 1
FaResult of step 2
FbResult of step 3
FcResult of step 4
FdResult of step 5
PvResult of step 6
LvLangelier Saturation Index, LSI

Worked example

Measured pH7.5
Water temperature80
Temperature unit°F
Calcium hardness (mg/L or ppm as CaCO₃)300
Alkalinity (mg/L or ppm as CaCO₃)100
Total dissolved solids, TDS (mg/L or ppm)1,000
Tendency of the waterPositive LSI — the water tends to deposit calcium carbonate (scale-forming)
Saturation pH, pHs7.48
Ryznar Stability Index, RSI7.46
Temperature used (°C)26.7
  1. Tc=(80−32)×59=26.6667
  2. Fa=log10⁡(1,000)−110=0.2
  3. Fb=−13.12×log10⁡(26.6667+273)+34.55=2.0565
  4. Fc=log10⁡(300)−0.4=2.07712
  5. Fd=log10⁡(100)=2
  6. Pv=9.3+0.2+2.0565−2.07712−2=7.47938
  7. Lv=7.5−7.47938=0.0206175

Langelier Saturation Index, LSI 0.02

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

Is this the same as the saturation index on my pool test kit?

It measures the same tendency, but a test kit or pool controller may use its maker's own method, so compare readings made with the same method. Follow the maker's instructions for which alkalinity to enter.

How do I read the Ryznar index?

It uses the same pHs. In the same Table 1: below 5.5 highly scale-forming, 5.5 to 6.2 relatively scale-forming, 6.2 to 6.8 balanced, 6.8 to 8 low corrosion, above 8 high corrosion.

What makes the LSI go up?

A higher pH raises the LSI directly; a higher temperature, calcium hardness or alkalinity lowers pHs and so raises the LSI; more dissolved solids raise pHs slightly and lower the LSI.

Related calculators