Skip to content
FiftyCalc Free calculators for all 50 states

NPSH Calculator

Test cases replayed : 2 of 2 match · Methodology · No outside source listed

NPSH available is the pressure margin above boiling at the pump inlet, in feet of liquid. Compare it with the NPSH required on the pump curve.

Result

Sample figures

NPSH available—ft

Pressure head above vapor pressure (ft) —

  • Margin over NPSH required (ft)—
  • Check—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

NPSH Calculator

Absolute pressure on the liquid surface (psia): enter 0 or more. Prefilled example: 14.696.

Vapor pressure of the liquid at pumping temperature (psia): enter 0 or more. Prefilled example: 0.36.

Specific gravity of the liquid: enter 0 or more. Prefilled example: 1.

Liquid level above the pump centerline (negative if below), in ft: enter a number. Prefilled example: 5.

Friction loss in the suction line, in ft: enter 0 or more. Prefilled example: 2.

NPSH required by the pump, in ft: enter 0 or more. Prefilled example: 10.

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Absolute pressure on the liquid surface (psia): enter 0 or more.
  2. Vapor pressure of the liquid at pumping temperature (psia): enter 0 or more.
  3. Specific gravity of the liquid: enter 0 or more.
  4. Liquid level above the pump centerline (negative if below), in ft: enter a number.
  5. Friction loss in the suction line, in ft: enter 0 or more.
  6. NPSH required by the pump, in ft: enter 0 or more.
  7. Read the result: NPSH available; the panel also shows Pressure head above vapor pressure (ft), Margin over NPSH required (ft) and Check.

How this calculator works

NPSHa = (p_surface − p_vapor) ÷ (ρ g) + z − h_f, where p_surface is the absolute pressure on the liquid, p_vapor its vapor pressure at the pumping temperature, ρ = SG × 1,000 kg/m³, g = 9.80665 m/s², z the height of the liquid level above the pump centerline and h_f the friction loss in the suction pipe.

Use absolute pressures (psia). Read the vapor pressure from a steam table or the fluid's data sheet; it rises quickly with temperature. Velocity head at the inlet is left out, as in most hand calculations.

Pumps need NPSHa above the NPSHr on their curve, usually with a safety margin, or the liquid can flash to vapor at the impeller (cavitation).

Unit conversions: NIST Special Publication 811, Appendix B (nist.gov, read October 27, 2026). 1 psi = 6,894.757 Pa, 1 ft = 0.3048 m.

The formula

  1. H=(ps−pv)×6,894.757293168361÷(sg×1,000×9.80665)0.3048
  2. N=H+z−hf
Symbols used in the formula
SymbolMeaningUnit
psAbsolute pressure on the liquid surface (psia)
pvVapor pressure of the liquid at pumping temperature (psia)
sgSpecific gravity of the liquid
zLiquid level above the pump centerline (negative if below)ft
hfFriction loss in the suction lineft
HPressure head above vapor pressureft
NNPSH availableft

Worked example

Absolute pressure on the liquid surface (psia)14.696
Vapor pressure of the liquid at pumping temperature (psia)0.36
Specific gravity of the liquid1
Liquid level above the pump centerline (negative if below)5 ft
Friction loss in the suction line2 ft
NPSH required by the pump10 ft
Pressure head above vapor pressure (ft)33.0683
Margin over NPSH required (ft)26.0683
CheckNPSH available exceeds NPSH required
  1. H=(14.696−0.36)×6,894.757293168361÷(1×1,000×9.80665)0.3048=33.0683
  2. N=33.0683+5−2=36.0683

NPSH available 36.0683 ft

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

What is the difference between NPSHa and NPSHr?

NPSHa is what your system supplies at the pump inlet; NPSHr is what the pump needs, given by its maker. NPSHa must be higher.

Does a suction lift reduce NPSH available?

Yes. When the liquid is below the pump, z is negative and is subtracted from the pressure head.

Why use absolute pressure?

Boiling depends on absolute pressure, so both the surface pressure and the vapor pressure must be in psia, not psig.

Related calculators