Skip to content
FiftyCalc Free calculators for all 50 states

Cutting Board Calculator

Test cases replayed : 2 of 2 match · Methodology · No outside source listed

Enter the size of the board you want and the size of the strips you will glue side by side. You get the number of strips, the glued width, the thickness left after flattening and the board feet of lumber to buy, saw kerf and waste included.

Result

Sample figures

Number of strips—

Glued-up width (inches) —

  • Finished thickness (inches)—
  • Total width ripped from the lumber, kerf included (inches)—
  • Lumber to buy (board feet)—

The unit choice applies to the fields you fill in. Results stay in the units written with them.

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Cutting Board Calculator

Units: switches the fields between the two unit systems.

Finished board width wanted, in in: enter 1 or more. Prefilled example: 12.

Finished board length, in in: enter 1 or more. Prefilled example: 18.

Width of each strip across the board, in in: enter 0.25 or more. Prefilled example: 1.5.

Thickness of the strips before flattening, in in: enter 0.25 or more. Prefilled example: 1.75.

Saw kerf lost per rip, in in: enter 0 or more. Prefilled example: 0.125.

Thickness removed when flattening, in in: enter 0 or more. Prefilled example: 0.25.

Extra length for trimming the ends, in in: enter 0 or more. Prefilled example: 2.

Waste allowance for defects and mistakes, in percent: enter a number from 0 to 100. Prefilled example: 15.

Affiliate link

This is an affiliate link. As an Amazon Associate I earn from qualifying purchases. This does not change the result.

Search Amazon for cutting board oil. Visit Amazon

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Units: switches the fields between the two unit systems.
  2. Finished board width wanted, in in: enter 1 or more.
  3. Finished board length, in in: enter 1 or more.
  4. Width of each strip across the board, in in: enter 0.25 or more.
  5. Thickness of the strips before flattening, in in: enter 0.25 or more.
  6. Saw kerf lost per rip, in in: enter 0 or more.
  7. Thickness removed when flattening, in in: enter 0 or more.
  8. Extra length for trimming the ends, in in: enter 0 or more.
  9. Waste allowance for defects and mistakes, in percent: enter a number from 0 to 100.
  10. Read the result: Number of strips; the panel also shows Glued-up width (inches), Finished thickness (inches), Total width ripped from the lumber, kerf included (inches) and Lumber to buy (board feet).

How this calculator works

Strips = finished width ÷ strip width, rounded up. Glued width = strips × strip width; trim it to size after glue-up if it is wider.

Each strip costs its own width plus one saw kerf in the lumber. Board feet = strips × (strip width + kerf) × strip thickness × (length + trim allowance) ÷ 144 × (1 + waste %); a board foot is 144 cubic inches, a 12 × 12 × 1 inch board.

Finished thickness = strip thickness − what flattening (planing or sanding) removes. The default sizes are an example; buy lumber by its actual, not nominal, thickness.

The formula

  1. N=ceil⁡(Ww2)
Symbols used in the formula
SymbolMeaningUnit
WFinished board width wantedin
w2Width of each strip across the boardin
NNumber of strips
ceil(x)the smallest whole number not below x.

Worked example

Finished board width wanted12 in
Finished board length18 in
Width of each strip across the board1.5 in
Thickness of the strips before flattening1.75 in
Saw kerf lost per rip0.125 in
Thickness removed when flattening0.25 in
Extra length for trimming the ends2 in
Waste allowance for defects and mistakes15%
Glued-up width (inches)12.00
Finished thickness (inches)1.50
Total width ripped from the lumber, kerf included (inches)13.00
Lumber to buy (board feet)3.63
  1. N=ceil⁡(121.5)=8

Number of strips 8

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

How many board feet is a cutting board?

A 12 × 18 inch board 1.5 inches thick holds 2.25 board feet of wood; with kerf, trim and 15% waste the default plan buys 3.63 board feet.

Edge grain or end grain?

This plan is for strips glued side by side (face or edge grain). An end-grain board is crosscut and glued a second time; plan the first glue-up here and add the second cut losses.

Which wood should I use?

Hardwoods such as maple, walnut and cherry are common choices. Use a food-safe finish.

Related calculators