Gutter Calculator
Test cases replayed : 2 of 2 match · Methodology · Sources
Enter the length of the eaves to gutter, the roof area that drains to them, the rainfall intensity you design for and your prices. You get the gutter sections, the runoff each downspout must carry and an estimate of the cost.
Result
Estimated cost
Gutter sections to buy
Reading the result
At a glance
What moves the result
Method and sources: How this calculator works, Sources
- Roof runoff at that intensity (gallons per minute)
- Runoff per downspout, if shared evenly (gallons per minute)
Estimate for planning only, not tax, legal, financial or medical advice. Check important figures with the official source listed on this page.
This browser did not allow copying. The sentence is in the box below, already selected: copy it with your keyboard or the menu.
How to use this calculator
Fill in the fields in this order; each step takes you to its field.
- Eave length to gutter, in ft: enter 0 or more.
- Roof area draining to the gutters, measured flat on the plan, in sq ft: enter 0 or more.
- Design rainfall intensity (inches per hour): enter a number from 0 to 20.
- Length of one gutter section (feet): choose 10 ft, 16 ft or 20 ft.
- Number of downspouts: enter a number from 1 to 40.
- Gutter price, installed or material ($ per foot): enter 0 or more.
- Price per downspout, in dollars: enter 0 or more.
- Read the result: Estimated cost; the panel also shows Gutter sections to buy, Roof runoff at that intensity (gallons per minute) and Runoff per downspout, if shared evenly (gallons per minute).
Sources
- NIST Handbook 44 (2026), Appendix C: General Tables of Units of Measurement National Institute of Standards and Technology (NIST) checked on 2026-11-01
How this calculator works
Sections = eave length ÷ section length, rounded up; add end caps, corners, hangers and outlets from the maker's instructions.
Runoff: 1 inch of rain on 1 square foot is 1/12 cubic foot, and a cubic foot holds 1,728 ÷ 231 = 7.48 US gallons. Flow (gpm) = roof area × intensity (in/h) ÷ 12 × 7.48 ÷ 60. Use the horizontal (plan) area of the roof that drains to the gutters.
The design intensity depends on your site: NOAA's precipitation frequency data (Atlas 14, hdsc.nws.noaa.gov) gives it by location, and the building code your state or city adopted sets which storm to design for. The default 3 in/h and the prices are examples.
Compare the flow per downspout with the capacity the gutter and downspout makers publish for their sizes. Cost = eave length × price per foot + downspouts × price each.
The formula
| Symbol | Meaning | Unit |
|---|---|---|
| Eave length to gutter | ft | |
| Number of downspouts | ||
| Gutter price, installed or material ($ per foot) | ||
| Price per downspout | $ | |
| Estimated cost | $ |
Worked example
| Eave length to gutter | 140 ft |
|---|---|
| Roof area draining to the gutters, measured flat on the plan | 1,800 sq ft |
| Design rainfall intensity (inches per hour) | 3 |
| Length of one gutter section (feet) | 10 ft |
| Number of downspouts | 4 |
| Gutter price, installed or material ($ per foot) | 6 |
| Price per downspout | $40 |
| Gutter sections to buy | 14 |
|---|---|
| Roof runoff at that intensity (gallons per minute) | 56.1 |
| Runoff per downspout, if shared evenly (gallons per minute) | 14.0 |
Estimated cost $1,000
Each step uses the unrounded value of the step before it; figures on this page are rounded for display.
Frequently asked questions
How many feet of gutter do I need?
The total length of the eaves where water runs off, plus a little for overlaps. Gable ends do not need gutters.
How many downspouts?
Enough that each one carries less than its rated flow at your design rainfall; long runs and big roofs need more.
Why measure the roof flat?
Rain falls vertically, so the water collected depends on the area seen from above, not on the slope length.