Skip to content
FiftyCalc Free calculators for all 50 states

Rake Wall Calculator

Test cases replayed : 3 of 3 match · Methodology · No outside source listed

A rake wall follows the roof slope, so each stud is a little taller than the last. Enter the wall length, the pitch and the low-end height to lay it out.

Result

Sample figures

Number of studs, both ends included—

Height gained from one stud to the next (in) —

  • Height at the high end (in)—
  • Length of the sloped top plate (ft)—
  • Wall area (sq ft)—
  • Roof angle (degrees)—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Rake Wall Calculator

Wall length, measured level, in ft: enter 1 or more. Prefilled example: 12.

Roof pitch, rise per 12 in of run, in in: enter a number from 0 to 24. Prefilled example: 6.

Height at the low end, in in: enter 1 or more. Prefilled example: 96.

Stud spacing on center (in)

Stud spacing on center (in): choose 12 in on center, 16 in on center, 19.2 in on center or 24 in on center. Prefilled example: 16 in on center.

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Wall length, measured level, in ft: enter 1 or more.
  2. Roof pitch, rise per 12 in of run, in in: enter a number from 0 to 24.
  3. Height at the low end, in in: enter 1 or more.
  4. Stud spacing on center (in): choose 12 in on center, 16 in on center, 19.2 in on center or 24 in on center.
  5. Read the result: Number of studs, both ends included; the panel also shows Height gained from one stud to the next (in), Height at the high end (in), Length of the sloped top plate (ft), Wall area (sq ft) and Roof angle (degrees).

How this calculator works

Height at a distance x from the low end = low-end height + x × pitch ÷ 12. Each stud is spacing × pitch ÷ 12 taller than the one before: 8 in for 16 in spacing on a 6-in-12 roof.

Studs = spacing count over the length, rounded up, plus one, so both ends get a stud. Sloped top plate = length × √(1 + (pitch ÷ 12)²). Area = length × average of the two end heights. Roof angle = arctan(pitch ÷ 12).

Heights are measured at the layout marks, to the same reference as the low-end height. Subtract plate thicknesses for stud cut lengths and mark the angled cut from the roof angle; follow your plans and local code for headers, bracing and nailing.

The formula

  1. Run=len×12
  2. St=ceil⁡(Runs)+1
Symbols used in the formula
SymbolMeaningUnit
lenWall length, measured levelft
sStud spacing on centerin
RunResult of step 1
StNumber of studs, both ends included
ceil(x)the smallest whole number not below x.

Worked example

Wall length, measured level12 ft
Roof pitch, rise per 12 in of run6 in
Height at the low end96 in
Stud spacing on center (in)16 in on center
Height gained from one stud to the next (in)8
Height at the high end (in)168
Length of the sloped top plate (ft)13.42
Wall area (sq ft)132.00
Roof angle (degrees)26.57
  1. Run=12×12=144
  2. St=ceil⁡(14416)+1=10

Number of studs, both ends included 10

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

How do I find the length of each stud in a rake wall?

Start with the shortest stud and add the height gain once per stud. On a 6/12 roof with studs 16 in apart, add 8 in each time.

What angle do I cut the top of the studs?

The roof angle shown, measured from square. A 6/12 pitch is about 26.57°.

Is a rake wall the same as a gable end wall?

The gable end is the triangle under the roof slope; a rake wall is any wall whose top follows that slope, often a full-height gable wall in a vaulted room.

Questions answered

Related calculators