Skip to content
FiftyCalc Free calculators for all 50 states

Wallpaper Calculator

Test cases replayed : 2 of 2 match · Methodology · No outside source listed

Enter the room perimeter, the wall height, the width of doors and windows to skip, and the roll size and pattern repeat from the label.

Result

Sample figures

Rolls to buy—

Length of one strip (inches) —

  • Strips from one roll—
  • Strips needed—
  • Wall area covered (square feet)—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Wallpaper Calculator

Room perimeter, in ft: enter 0 or more. Prefilled example: 48.

Wall height, in ft: enter 0 or more. Prefilled example: 8.

Width of doors and large windows, in ft: enter 0 or more. Prefilled example: 6.

Roll width, in in: enter 0.1 or more. Prefilled example: 20.5.

Roll length, in ft: enter 0.1 or more. Prefilled example: 33.

Pattern repeat (0 if none), in in: enter 0 or more. Prefilled example: 0.

Affiliate link

This is an affiliate link: FiftyCalc may earn a commission if you buy through it. This does not change the result.

Homestyler is an online home design tool with a free basic plan and paid memberships. Visit Homestyler

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Room perimeter, in ft: enter 0 or more.
  2. Wall height, in ft: enter 0 or more.
  3. Width of doors and large windows, in ft: enter 0 or more.
  4. Roll width, in in: enter 0.1 or more.
  5. Roll length, in ft: enter 0.1 or more.
  6. Pattern repeat (0 if none), in in: enter 0 or more.
  7. Read the result: Rolls to buy; the panel also shows Length of one strip (inches), Strips from one roll, Strips needed and Wall area covered (square feet).

How this calculator works

Strips needed = wall run (perimeter − openings) ÷ roll width, rounded up. Each strip is the wall height plus one pattern repeat for matching; strips per roll = roll length ÷ strip length, rounded down, because offcuts are too short for another strip. Rolls = strips needed ÷ strips per roll, rounded up.

Roll sizes differ between makers (single and double rolls); read them on the label.

The formula

  1. Sl=H×12+rep
  2. Pr=floor⁡(rl×12Sl)
  3. Ns=ceil⁡((P−o)×12rw)
  4. R=ceil⁡(NsPr)
Symbols used in the formula
SymbolMeaningUnit
PRoom perimeterft
HWall heightft
oWidth of doors and large windowsft
rwRoll widthin
rlRoll lengthft
repPattern repeat (0 if none)in
SlLength of one stripinches
PrStrips from one roll
NsStrips needed
RRolls to buy
floor(x)the largest whole number not above x.
ceil(x)the smallest whole number not below x.

Worked example

Room perimeter48 ft
Wall height8 ft
Width of doors and large windows6 ft
Roll width20.5 in
Roll length33 ft
Pattern repeat (0 if none)0 in
Length of one strip (inches)96.0
Strips from one roll4
Strips needed25
Wall area covered (square feet)336
  1. Sl=8×12+0=96
  2. Pr=floor⁡(33×1296)=4
  3. Ns=ceil⁡((48−6)×1220.5)=25
  4. R=ceil⁡(254)=7

Rolls to buy 7

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

How many rolls for a 48-foot room with 8-foot walls?

With 6 feet of openings and 20.5 × 33-foot rolls: 25 strips, 4 strips per roll, so 7 rolls.

Why does the pattern repeat matter?

Each strip must start at the same point of the pattern, so it wastes up to one repeat per strip.

Questions answered

Related calculators