Skip to content
FiftyCalc Free calculators for all 50 states

Bridge Rectifier Calculator

Test cases replayed : 2 of 2 match · Methodology · No outside source listed

A bridge rectifier turns AC into pulsing DC through four diodes, two of which conduct at any time. Enter the transformer voltage, the diode drop, the load and the filter capacitor.

Result

Sample figures

Average DC output with the capacitor (V)—

Peak input voltage (V) —

  • Peak DC output after two diode drops (V)—
  • Average DC output with no capacitor (V)—
  • Ripple voltage with the capacitor (V peak to peak)—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Bridge Rectifier Calculator

AC input voltage (V rms): enter 0 or more. Prefilled example: 12.

Forward drop of one diode, in V: enter 0 or more. Prefilled example: 0.7.

Mains frequency, in Hz: enter 1 or more. Prefilled example: 60.

Load current, in A: enter 0 or more. Prefilled example: 1.

Filter capacitor, in µF: enter 0 or more. Prefilled example: 2,200.

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. AC input voltage (V rms): enter 0 or more.
  2. Forward drop of one diode, in V: enter 0 or more.
  3. Mains frequency, in Hz: enter 1 or more.
  4. Load current, in A: enter 0 or more.
  5. Filter capacitor, in µF: enter 0 or more.
  6. Read the result: Average DC output with the capacitor (V); the panel also shows Peak input voltage (V), Peak DC output after two diode drops (V), Average DC output with no capacitor (V) and Ripple voltage with the capacitor (V peak to peak).

How this calculator works

Peak input Vp = Vrms × √2. In a bridge, current passes through two diodes in series, so the peak output is Vp − 2Vf.

Without a capacitor, the average of a full-wave rectified sine is 2 × Vpeak ÷ π. With a capacitor C, the ripple is about ΔV = I ÷ (2 f C), because the capacitor is recharged twice per mains cycle; the average output is then about Vpeak − ΔV ÷ 2.

These are the usual first-order estimates; real ripple also depends on transformer resistance and the diode's conduction angle.

The formula

  1. Vpk=v×2
  2. Vo=Vpk−2×vf
  3. Rip=il2×f×cuf÷1,000,000
  4. Vdc=Vo−Rip2
Symbols used in the formula
SymbolMeaningUnit
vAC input voltage (V rms)
vfForward drop of one diodeV
fMains frequencyHz
ilLoad currentA
cufFilter capacitorµF
VpkPeak input voltageV
VoPeak DC output after two diode dropsV
RipRipple voltage with the capacitor (V peak to peak)
VdcAverage DC output with the capacitorV

Worked example

AC input voltage (V rms)12
Forward drop of one diode0.7 V
Mains frequency60 Hz
Load current1 A
Filter capacitor2,200 µF
Peak input voltage (V)16.9706
Peak DC output after two diode drops (V)15.5706
Average DC output with no capacitor (V)9.9125
Ripple voltage with the capacitor (V peak to peak)3.7879
  1. Vpk=12×2=16.9706
  2. Vo=16.9706−2×0.7=15.5706
  3. Rip=12×60×2,200÷1,000,000=3.78788
  4. Vdc=15.5706−3.787882=13.6766

Average DC output with the capacitor (V) 13.6766

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

Why subtract two diode drops?

In a bridge, two diodes conduct in series on each half cycle, so two forward drops are lost from the peak.

How do I reduce ripple?

Use a larger capacitor or a lower load current: ripple falls in proportion to 1 ÷ C. Doubling C halves the ripple.

Related calculators