Skip to content
FiftyCalc Free calculators for all 50 states

Wheel Offset Calculator

Test cases replayed : 2 of 2 match · Methodology · No outside source listed

Enter the overall width and backspacing of your current and new wheels to get each offset and the change in inner clearance and outer poke.

Result

Sample figures

New offset—mm

Current offset (mm) —

  • Inner edge moves toward the suspension by (in)—
  • Outer edge moves out toward the fender by (in)—

The unit choice applies to the fields you fill in. Results stay in the units written with them.

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Wheel Offset Calculator

Units: switches the fields between the two unit systems.

Current wheel overall width, flange to flange, in in: enter 1 or more. Prefilled example: 9.

Current backspacing, in in: enter 0 or more. Prefilled example: 5.

New wheel overall width, flange to flange, in in: enter 1 or more. Prefilled example: 10.

New backspacing, in in: enter 0 or more. Prefilled example: 5.5.

Affiliate link

This is an affiliate link: FiftyCalc may earn a commission if you buy through it. This does not change the result.

KSP Performance sells vehicle parts, including leveling lift kits. Visit KSP Performance

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Units: switches the fields between the two unit systems.
  2. Current wheel overall width, flange to flange, in in: enter 1 or more.
  3. Current backspacing, in in: enter 0 or more.
  4. New wheel overall width, flange to flange, in in: enter 1 or more.
  5. New backspacing, in in: enter 0 or more.
  6. Read the result: New offset; the panel also shows Current offset (mm), Inner edge moves toward the suspension by (in) and Outer edge moves out toward the fender by (in).

How this calculator works

Offset is the distance from the wheel's centerline to its mounting face; backspacing is the distance from the inner flange to the mounting face. So offset = backspacing − overall width ÷ 2, converted to millimeters with 1 in = 25.4 mm (NIST SP 811, Appendix B.9, nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9, read 2026-10-27). Positive offset puts the mounting face outboard of the centerline.

Inner clearance changes by the backspacing difference; the outer edge (front spacing = width − backspacing) changes by the front spacing difference. A negative result means the edge moves the other way. Measure overall width across the flanges, not the nominal rim width.

The formula

  1. O2=(b2−w22)×25.4
Symbols used in the formula
SymbolMeaningUnit
w2New wheel overall width, flange to flangein
b2New backspacingin
O2New offsetmm

Worked example

Current wheel overall width, flange to flange9 in
Current backspacing5 in
New wheel overall width, flange to flange10 in
New backspacing5.5 in
Current offset (mm)12.7
Inner edge moves toward the suspension by (in)0.5
Outer edge moves out toward the fender by (in)0.5
  1. O2=(5.5−102)×25.4=12.7

New offset 12.7 mm

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

What offset is a 9 in wide wheel with 5 in backspacing?

+12.7 mm, since the mounting face sits 0.5 in outboard of the centerline.

Can two wheels have the same offset but fit differently?

Yes. A 10 in wheel with 5.5 in backspacing also has +12.7 mm offset, but it sits 0.5 in closer to the suspension and 0.5 in farther out than the 9 in wheel.

Related calculators