Skip to content
FiftyCalc Free calculators for all 50 states

Capacitor Charge Time Calculator

Test cases replayed : 2 of 2 match · Methodology · No outside source listed

A capacitor charging through a resistor follows an exponential curve set by the time constant τ = RC. Enter the resistor, the capacitor and the supply.

Result

Sample figures

Time to reach the target percentage—seconds

Time constant τ = RC (seconds) —

  • Time to about 99.3% charge, 5τ (seconds)—
  • Capacitor voltage after the elapsed time (V)—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Capacitor Charge Time Calculator

Resistance, in kΩ: enter 0 or more. Prefilled example: 10.

Capacitance, in µF: enter 0 or more. Prefilled example: 100.

Supply voltage, in V: enter 0 or more. Prefilled example: 9.

Target charge (% of supply): enter a number from 0 to 99.99. Prefilled example: 90.

Elapsed time for the voltage check, in seconds: enter 0 or more. Prefilled example: 1.

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Resistance, in kΩ: enter 0 or more.
  2. Capacitance, in µF: enter 0 or more.
  3. Supply voltage, in V: enter 0 or more.
  4. Target charge (% of supply): enter a number from 0 to 99.99.
  5. Elapsed time for the voltage check, in seconds: enter 0 or more.
  6. Read the result: Time to reach the target percentage; the panel also shows Time constant τ = RC (seconds), Time to about 99.3% charge, 5τ (seconds) and Capacitor voltage after the elapsed time (V).

How this calculator works

Charging through a resistor: V(t) = Vs × (1 − e^(−t/τ)), with τ = R × C (ohms × farads = seconds). Solving for time, the capacitor reaches a fraction p of the supply after t = −τ × ln(1 − p).

After one τ the capacitor holds 1 − e⁻¹ ≈ 63.2% of the supply, and after 5τ about 99.3%, the usual rule for "fully charged".

The formula

  1. τ=rk×1,000×cuf1,000,000
  2. Tp=−τ×ln⁡(1−p100)
Symbols used in the formula
SymbolMeaningUnit
rkResistancekΩ
cufCapacitanceµF
pTarget charge (% of supply)
τTime constant τ = RCseconds
TpTime to reach the target percentageseconds

Worked example

Resistance10 kΩ
Capacitance100 µF
Supply voltage9 V
Target charge (% of supply)90
Elapsed time for the voltage check1 seconds
Time constant τ = RC (seconds)1
Time to about 99.3% charge, 5τ (seconds)5
Capacitor voltage after the elapsed time (V)5.6891
  1. τ=10×1,000×1001,000,000=1
  2. Tp=−1×ln⁡(1−90100)=2.30259

Time to reach the target percentage 2.3026 seconds

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

How long does 10 kΩ and 100 µF take to charge?

τ = 1 second, so about 5 seconds to be practically full and 2.3026 seconds to reach 90%.

Does the supply voltage change the charge time?

No. The time to a given percentage depends only on R and C; the voltage only scales the curve.

Related calculators