Skip to content
FiftyCalc Free calculators for all 50 states

Fuel Injector Calculator

Test cases replayed : 2 of 2 match · Methodology · No outside source listed

Enter the crankshaft horsepower you plan to make, the engine's BSFC, the number of injectors and the highest duty cycle you will run them at.

Result

Sample figures

Injector flow needed (lb/hr each)—

Injector flow needed (cc/min each) —

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Fuel Injector Calculator

Target power (at the crank), in hp: enter 0 or more. Prefilled example: 400.

BSFC (lb/hp·h, from your engine builder; example): enter 0 or more. Prefilled example: 0.5.

Number of injectors: enter 1 or more. Prefilled example: 8.

Maximum duty cycle, in percent: enter a number from 0 to 100. Prefilled example: 80.

Fuel density (lb/gal, example for gasoline): enter 0 or more. Prefilled example: 6.0.

Affiliate link

This is an affiliate link. As an Amazon Associate I earn from qualifying purchases. This does not change the result.

Search Amazon for fuel injectors. Visit Amazon

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Target power (at the crank), in hp: enter 0 or more.
  2. BSFC (lb/hp·h, from your engine builder; example): enter 0 or more.
  3. Number of injectors: enter 1 or more.
  4. Maximum duty cycle, in percent: enter a number from 0 to 100.
  5. Fuel density (lb/gal, example for gasoline): enter 0 or more.
  6. Read the result: Injector flow needed (lb/hr each); the panel also shows Injector flow needed (cc/min each).

How this calculator works

Injector size = horsepower × BSFC ÷ (number of injectors × maximum duty cycle). BSFC (brake specific fuel consumption) is the pounds of fuel the engine burns per horsepower per hour; boosted engines usually burn more per horsepower than naturally aspirated ones.

cc/min = lb/hr ÷ density (lb/gal) × 3,785.412 mL/gal ÷ 60. 1 gal = 3.785412 L (NIST Special Publication 811, Appendix B.9 (https://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9, read 2026-10-27)). The density default is an example within the range of the U.S. Department of Energy (EERE) table "Properties of Fuels", gasoline density 6.0–6.5 lb/gal at 60 °F, as reproduced at https://www.BuildItSolar.com/References/EEREfueltable.pdf (read 2026-10-27); enter your fuel's figure (E85 and race fuels differ).

The formula

  1. Lb=hp×bn×dc÷100
Symbols used in the formula
SymbolMeaningUnit
hpTarget power (at the crank)hp
bBSFC (lb/hp·h, from your engine builder; example)
nNumber of injectors
dcMaximum duty cycle%
LbInjector flow needed (lb/hr each)

Worked example

Target power (at the crank)400 hp
BSFC (lb/hp·h, from your engine builder; example)0.5
Number of injectors8
Maximum duty cycle80%
Fuel density (lb/gal, example for gasoline)6
Injector flow needed (cc/min each)329
  1. Lb=400×0.58×80÷100=31.25

Injector flow needed (lb/hr each) 31.3

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

What size injectors for 400 hp with 8 injectors, BSFC 0.5 and 80% duty?

31.3 lb/hr each, about 329 cc/min with gasoline at 6.0 lb/gal.

Why not size for 100% duty cycle?

At 100% the injector stays open and can no longer meter fuel; a margin keeps control at full power.

Related calculators