Skip to content
FiftyCalc Free calculators for all 50 states

MOSFET Calculator

Test cases replayed : 3 of 3 match · Methodology · No outside source listed

Find whether an n-channel MOSFET is off, in the triode region or in saturation, and the drain current it conducts, with the long-channel square-law model.

Result

Sample figures

Drain current ID—mA

Overdrive voltage VGS − Vth (V) —

  • Operating region—
  • Transconductance gm (mS)—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

MOSFET Calculator

Gate-source voltage VGS, in V: enter a number. Prefilled example: 2.

Drain-source voltage VDS, in V: enter a number. Prefilled example: 3.

Threshold voltage Vth, in V: enter a number. Prefilled example: 0.7.

Process transconductance μnCox (µA/V²): enter 0 or more. Prefilled example: 200.

Width-to-length ratio W/L: enter 0 or more. Prefilled example: 10.

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Gate-source voltage VGS, in V: enter a number.
  2. Drain-source voltage VDS, in V: enter a number.
  3. Threshold voltage Vth, in V: enter a number.
  4. Process transconductance μnCox (µA/V²): enter 0 or more.
  5. Width-to-length ratio W/L: enter 0 or more.
  6. Read the result: Drain current ID; the panel also shows Overdrive voltage VGS − Vth (V), Operating region and Transconductance gm (mS).

How this calculator works

Long-channel square-law (Shichman–Hodges) model of an n-channel MOSFET, with k = μnCox × W/L: cutoff when VGS ≤ Vth (ID = 0); triode when VDS < VGS − Vth, ID = k × [(VGS − Vth) × VDS − VDS²/2]; saturation otherwise, ID = ½ × k × (VGS − Vth)².

Transconductance gm = ∂ID/∂VGS: k × (VGS − Vth) in saturation and k × VDS in triode. The model ignores channel-length modulation and short-channel effects, so modern small transistors depart from it; for a p-channel device use magnitudes.

The formula

  1. Vov=vgs−vt
  2. Reg={0if Vov≤01if vds<Vov2otherwise
  3. Id={0if Reg=0kp×0.000001×wl×(Vov×vds−vds22)×1,000if Reg=10.5×kp×0.000001×wl×Vov2×1,000otherwise
Symbols used in the formula
SymbolMeaningUnit
vgsGate-source voltage VGSV
vdsDrain-source voltage VDSV
vtThreshold voltage VthV
kpProcess transconductance μnCoxµA/V²
wlWidth-to-length ratio W/L
VovOverdrive voltage VGS − VthV
RegOperating region
IdDrain current IDmA

Worked example

Gate-source voltage VGS2 V
Drain-source voltage VDS3 V
Threshold voltage Vth0.7 V
Process transconductance μnCox (µA/V²)200
Width-to-length ratio W/L10
Overdrive voltage VGS − Vth (V)1.3
Operating regionSaturation
Transconductance gm (mS)2.6
  1. Vov=2−0.7=1.3
  2. Reg=2
  3. Id=0.5×200×0.000001×10×1.32×1,000=1.69

Drain current ID 1.69 mA

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

How do I know a MOSFET is in saturation?

When VGS is above the threshold and VDS ≥ VGS − Vth: the channel is pinched off at the drain end and the current barely depends on VDS.

Is MOSFET saturation the same as BJT saturation?

No, they are opposites: a saturated MOSFET acts as a current source (used in amplifiers), while a saturated BJT acts as a closed switch.

Related calculators