Skip to content
FiftyCalc Free calculators for all 50 states

Fit Tolerance Calculator

Test cases replayed : 4 of 4 match · Methodology · No outside source listed

Enter the basic size and the upper and lower deviations of the hole and of the shaft, in micrometers, as read from your drawing or tolerance table. The calculator gives the limits of size, the extreme clearances and whether the fit is clearance, transition or interference.

Result

Sample figures

Type of fit—

Maximum clearance ES − ei (µm; negative = interference) —

  • Minimum clearance EI − es (µm; negative = interference)—
  • Hole maximum size (mm)—
  • Hole minimum size (mm)—
  • Shaft maximum size (mm)—
  • Shaft minimum size (mm)—
  • Hole tolerance ES − EI (µm)—
  • Shaft tolerance es − ei (µm)—
  • Fit tolerance, sum of both (µm)—

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Fit Tolerance Calculator

Basic (nominal) size, in mm: enter 0 or more. Prefilled example: 25.

Hole upper deviation ES, in µm: enter a number. Prefilled example: 21.

Hole lower deviation EI, in µm: enter a number. Prefilled example: 0.

Shaft upper deviation es, in µm: enter a number. Prefilled example: -20.

Shaft lower deviation ei, in µm: enter a number. Prefilled example: -33.

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Basic (nominal) size, in mm: enter 0 or more.
  2. Hole upper deviation ES, in µm: enter a number.
  3. Hole lower deviation EI, in µm: enter a number.
  4. Shaft upper deviation es, in µm: enter a number.
  5. Shaft lower deviation ei, in µm: enter a number.
  6. Read the result: Type of fit; the panel also shows Maximum clearance ES − ei (µm; negative = interference), Minimum clearance EI − es (µm; negative = interference), Hole maximum size (mm), Hole minimum size (mm), Shaft maximum size (mm), Shaft minimum size (mm), Hole tolerance ES − EI (µm), Shaft tolerance es − ei (µm) and Fit tolerance, sum of both (µm).

How this calculator works

Limits of size = basic size + deviation (1 µm = 0.001 mm). Hole: maximum D + ES, minimum D + EI. Shaft: maximum D + es, minimum D + ei. These are the terms of the ISO system of limits and fits (ISO 286-1) and of ANSI/ASME B4.2.

Maximum clearance = largest hole − smallest shaft = ES − ei. Minimum clearance = smallest hole − largest shaft = EI − es. A negative clearance is an interference.

Clearance fit: minimum clearance ≥ 0 (at exactly 0 the largest shaft equals the smallest hole). Interference fit: maximum clearance ≤ 0 (at exactly 0 the smallest shaft equals the largest hole). Otherwise the fit is a transition fit. The fit tolerance (variation of the clearance) equals the hole tolerance plus the shaft tolerance.

The calculator does not hold the ISO 286-2 tables of standard deviations (such as H7 or g6); read the deviations for your size range from the standard, your drawing or your supplier's table and enter them.

Worked example

Basic (nominal) size25 mm
Hole upper deviation ES21 µm
Hole lower deviation EI0 µm
Shaft upper deviation es-20 µm
Shaft lower deviation ei-33 µm
Type of fitClearance fit: the shaft is never larger than the hole (zero gap at the limit)
Hole maximum size (mm)25.021
Hole minimum size (mm)25
Shaft maximum size (mm)24.98
Shaft minimum size (mm)24.967
Maximum clearance ES − ei (µm; negative = interference)54
Minimum clearance EI − es (µm; negative = interference)20
Hole tolerance ES − EI (µm)21
Shaft tolerance es − ei (µm)13
Fit tolerance, sum of both (µm)34

Frequently asked questions

Where do I find the deviations for a fit such as H7/g6?

In ISO 286-2 or ANSI/ASME B4.2 tables, by size range and tolerance grade, or on the part drawing. For hole-basis fits (H), the hole's lower deviation EI is 0.

What does a negative maximum clearance mean?

Even the largest hole is smaller than the smallest shaft, so every pair of parts is an interference (press) fit.

Can I use inches?

Yes, as long as every value uses the same scale: the size results are basic size + deviation ÷ 1,000, so enter the basic size in inches and the deviations in thousandths of an inch.

Related calculators