Skip to content
FiftyCalc Free calculators for all 50 states

Material Removal Rate Calculator

Test cases replayed : 3 of 3 match · Methodology · No outside source listed

Choose the operation; the three fields below change meaning with it, as their labels say.

Result

Sample figures

Material removal rate (cubic inches per minute)—

Material removal rate (cm³ per minute) —

Estimate for planning only, not tax, legal, financial or medical advice. This calculator uses the method explained on this page.

Material Removal Rate Calculator

Operation

Operation: choose Milling, Turning or Drilling. Prefilled example: Milling.

Milling: width of cut (in) · Turning: cutting speed (SFM) · Drilling: drill diameter, in in: enter 0 or more. Prefilled example: 0.5.

Milling: depth of cut (in) · Turning: feed (in/rev) · Drilling: feed (in/rev): enter 0 or more. Prefilled example: 0.25.

Milling: table feed (in/min) · Turning: depth of cut (in) · Drilling: spindle speed, in RPM: enter 0 or more. Prefilled example: 20.

How to use this calculator

Fill in the fields in this order; each step takes you to its field.

  1. Operation: choose Milling, Turning or Drilling.
  2. Milling: width of cut (in) · Turning: cutting speed (SFM) · Drilling: drill diameter, in in: enter 0 or more.
  3. Milling: depth of cut (in) · Turning: feed (in/rev) · Drilling: feed (in/rev): enter 0 or more.
  4. Milling: table feed (in/min) · Turning: depth of cut (in) · Drilling: spindle speed, in RPM: enter 0 or more.
  5. Read the result: Material removal rate (cubic inches per minute); the panel also shows Material removal rate (cm³ per minute).

How this calculator works

Milling: MRR = width of cut × depth of cut × table feed. Turning: MRR = 12 × cutting speed (ft/min) × feed (in/rev) × depth of cut (the 12 turns feet of surface into inches). Drilling: MRR = π × D² ÷ 4 × feed per revolution × rpm.

Each formula is the volume swept per minute: the cross-section of the cut times the speed at which it advances. Unit factors from NIST Handbook 44 (2026), Appendix C, General Tables of Units of Measurement (https://www.nist.gov/document/2026-nist-handbook-44-appendix-c), read on 2026-10-27: 1 inch = 2.54 cm exactly, 1 cubic foot = 1,728 cubic inches, 1 gallon = 231 cubic inches = 3.785411784 L, 1 cubic yard = 27 cubic feet, 1 pound = 0.45359237 kg, 1 ton = 2,000 pounds. 1 cubic inch = 16.387064 cm³.

The formula

  1. Mrr={a×b×fif m=112×a×b×fif m=2π×a24×b×fotherwise
Symbols used in the formula
SymbolMeaningUnit
mOperation (1: Milling; 2: Turning; 3: Drilling)
aMilling: width of cut (in) · Turning: cutting speed (SFM) · Drilling: drill diameterin
bMilling: depth of cut (in) · Turning: feed (in/rev) · Drilling: feed (in/rev)
fMilling: table feed (in/min) · Turning: depth of cut (in) · Drilling: spindle speedRPM
MrrMaterial removal ratecubic inches per minute

Worked example

OperationMilling
Milling: width of cut (in) · Turning: cutting speed (SFM) · Drilling: drill diameter0.5 in
Milling: depth of cut (in) · Turning: feed (in/rev) · Drilling: feed (in/rev)0.25
Milling: table feed (in/min) · Turning: depth of cut (in) · Drilling: spindle speed20 RPM
Material removal rate (cm³ per minute)40.97
  1. Mrr=0.5×0.25×20=2.5

Material removal rate (cubic inches per minute) 2.5

Each step uses the unrounded value of the step before it; figures on this page are rounded for display.

Frequently asked questions

What is the MRR of a 0.5-inch wide, 0.25-inch deep cut at 20 in/min?

0.5 × 0.25 × 20 = 2.5 cubic inches per minute.

What MRR does turning at 400 SFM, 0.01 in/rev and 0.1 inch deep give?

12 × 400 × 0.01 × 0.1 = 4.8 cubic inches per minute.

Related calculators